Licensed CA LIC# 1077901 · C-53 Swimming Pool Contractor

Mon–Sat, 7 AM – 5 PM

A flat illustration of a pool equipment pad with a tall filter tank and two pool pumps on a concrete base beside a curved pool
Repairs

Your pool pump stopped doing its job. This is what to check first and when to call a pro.

Pool pump not working? Safe checks for a pump that won't start, hums, loses prime, or has low flow, plus how to tell a pool pump repair from a replacement.

By Adam Aguirre, Owner & Lead Technician 6 min read
Quick answer

Why won't a pool pump start?

Most of the time it isn't getting a signal or power. Pentair's IntelliFlo3 installation and maintenance guide says its pump stops until an alarm is resolved, and shows a fault code. Check the timer, the automation schedule, and the breaker before anything else.

If the breaker trips again after one reset, leave it off. A breaker that won't hold means a fault on that circuit.

In this guide
  1. Why won't a pool pump start?
  2. Safe checks for a pump that won't run
  3. A humming pool pump that won't spin
  4. Why does a pool pump lose prime?
  5. Pump runs but the flow is weak
  6. Keep the pool safe while the pump is down
  7. Repair or replace a pool pump
  8. Want the pump looked at by a pro?
  9. Frequently asked questions

A pool pump that's not working usually won't start, hums without spinning, loses prime, or runs with weak flow. You can safely check power, the schedule, the water level, the baskets, and the lid seal.

A humming motor, repeat breaker trips, or a drive fault code means it's time for a technician.

I'm Adam, owner and lead technician at Adam's Pool & Spa in Long Beach. I'm Jandy Certified and a Pentair Expert Installer, and a dead pump is one of the repairs we see most. If your pump is loud rather than stopped, read our guide on why a pool pump gets so loud.

Safe checks for a pump that won't run

These are the checks a homeowner can make without opening anything.

  1. Check the schedule. Make sure the timer or app has the pump in an on window.
  2. Check the breaker and GFCI. Reset each once. If either trips again, stop.
  3. Read the drive display. Variable speed pumps show alarm codes. Write the code down.
  4. Check the water level. It should sit near the middle of the skimmer opening.
  5. Empty the baskets. Clear the skimmer basket and the pump strainer basket with the power off.
  6. Look at the lid O-ring. A dry, cracked, or dirty O-ring lets air in.

The IntelliFlo3 guide lists overheat, over current, and voltage alarms. Overheat can come from a blocked cooling fan or very high air temperature. Over current can mean debris or worn parts loading the motor. Those last two are technician calls.

A humming pool pump that won't spin

A hum means the motor has power but can't turn. The usual causes are a failed capacitor, a seized bearing, or a jammed impeller.

Shut it off at the breaker right away. A motor that hums without spinning heats up fast. Leave the capacitor to a pro. On its variable speed pump, Pentair warns the drive holds a 230 volt charge even with the power off.

Why does a pool pump lose prime?

Because air is getting into the suction side. According to Pentair's IntelliFlo3 guide, common causes are a suction leak, a skimmer pulling air, a worn lid O-ring, or a low strainer pot. Fill the strainer pot with water up to the suction port, seat the lid, and restart.

Top up the pool if the skimmer is gulping air. If it still won't hold prime, the leak is likely in a fitting or valve, and that's a repair.

Pentair's guide adds a safety note. Don't open the strainer pot if the pump has been running dry. The water inside can build pressure and get scalding hot. Make sure the valves are open and the pot is cool before you open it.

Pump runs but the flow is weak

Low flow usually means something is blocking the water's path. The IntelliFlo3 guide lists a clogged strainer basket, air in the suction line, a clogged impeller, or a pump below its set speed.

ENERGY STAR's pool pump guidance says to clear the pump and skimmer baskets regularly so water flow isn't hampered. A dirty filter does the same thing from the other side. Check these in order:

  • Skimmer and pump baskets
  • Filter pressure, and clean the filter if it's high
  • Valves set the way they normally sit
  • The pump's programmed speed on a variable speed model

Weak flow matters more than it looks. It can keep the heater from firing and stop a cleaner from working.

Keep the pool safe while the pump is down

A pool without circulation loses ground quickly. A U.S. Department of Energy pool pump measure guide calls one full turnover of the water every 24 hours the minimum. It warns that falling short raises the risk of algae and pathogens.

Until the pump is fixed, test chlorine daily, keep it up, and skim by hand. Once the pump runs again, give it at least one full turnover a day. Our guide on how long to run your pool pump shows how to work out that number.

Repair or replace a pool pump

Repair a newer pump with one clear fault, like a seal, capacitor, or bearing. Price a replacement when the pump is older and failing in more than one place, or the motor has burned out.

Situation Usual call
Newer pump, one failed part Repair
Leaking shaft seal on an otherwise sound pump Repair
Older pump with noise, leaks, and trips Replace
Burned out single speed motor Replace, often with variable speed

If you're replacing, our guide on whether variable speed pool pumps are worth it covers the energy side. Handy owners can read our steps for how to replace a pool pump. The wiring and bonding still belong with a qualified pro.

The questions Long Beach pool owners ask most when the pump quits, answered plainly.

Want the pump looked at by a pro?

A stopped pump is worth fixing fast, before the water turns. At Adam's Pool & Spa, I'll find out whether it's power, air, a part, or the motor. We work across Long Beach and nearby neighborhoods, and we're Jandy Certified and a Pentair Expert Installer. You can also read about our pool pump repair service, or schedule a visit and I'll get it running.

Adam is the founder, owner, and lead technician of Adam's Pool & Spa, working on pools in Long Beach and nearby LA County for about fifteen years. He is Jandy Certified and a Pentair Expert Installer, and he built the business on education-first, anti-pressure service, including the "Pool School" session each new client gets.

FAQ

Frequently asked questions

Why won't my pool pump turn on?

Start with power and schedule. Check the timer or automation schedule, the breaker, and any GFCI on the pump circuit. Variable speed pumps also stop on their own when they detect a fault, and show a code on the drive. If the pump still won't start after those checks, the fault is in the motor or drive and needs a technician.

Why does my pool pump keep losing prime?

Usually air is getting into the suction side. Pentair's IntelliFlo3 guide lists an air leak in the suction line, a low pool level that lets the skimmer pull air, a worn lid O-ring, or too little water in the strainer pot. Fix the water level and the lid seal first.

Is it safe to run a pool pump that's humming?

No. A pump that hums without spinning is getting power but can't turn, and running it that way can overheat the motor. Shut it off at the breaker and call for a repair. Common causes are a failed capacitor, a seized bearing, or debris jamming the impeller.

Should I repair or replace my pool pump?

Repair usually makes sense on a newer pump with one clear fault, like a seal or a capacitor. Replacement makes more sense on an older pump that's failing in more than one place. In California, a replacement is usually a variable speed pump because of state efficiency rules.

What happens to my pool while the pump is down?

The water stops filtering and circulating, so chlorine gets used up faster in some spots and algae gets a head start. Keep the chlorine up, skim by hand, and get the pump running soon. Once it's back, run at least one full turnover a day.

Adam, owner of Adam's Pool and Spa Service
Written by
Adam
Owner & Lead Technician, Adam's Pool & Spa

Adam is the founder, owner, and lead technician of Adam's Pool & Spa, serving Long Beach and surrounding LA County for about 15 years. He is Jandy Certified and a Pentair Expert Installer, and he built the business on education-first, anti-pressure service — including the Pool School session every new client gets.

Rather have a pro handle it?

Pump still down after the safe checks? Schedule a visit and we'll find the cause and give you repair and replacement options before any work starts.

Call now Schedule