In this guide
- Why won't a pool heater fire?
- Safe checks you can make yourself
- What do pool heater error codes mean?
- Why won't a heat pump heat in cool months?
- Gas heater runs but the water stays cold
- When to stop and call a pro
- If you smell gas near the heater
- Repair or replace an old pool heater
- Want the heater checked by a pro?
- Frequently asked questions
When a pool heater won't fire, check the pump, the filter and baskets, the valves, and the heater's setpoint. When it runs but won't heat in cool months, a heat pump may be fighting cold air.
A gas heater with that problem usually has a flow or heat exchanger issue. Anything past those checks belongs to a qualified technician.
I'm Adam, owner and lead technician at Adam's Pool & Spa in Long Beach. I'm Jandy Certified and a Pentair Expert Installer. A cold heater is one of the most common calls we get once the nights cool off. This guide covers what you can safely check yourself and where our pool heater repair service takes over.
Safe checks you can make yourself
These checks stay on the outside of the heater. Do them in this order.
- Confirm the heater is on. Check that it's set to pool or spa and the setpoint is above the current water temperature.
- Confirm the pump is running. If your pump is on a timer or schedule, make sure it's in an on window.
- Clean the baskets and filter. Empty the skimmer and pump baskets, and clean the filter if pressure is high.
- Check the valves. Make sure the valves to the heater and the pool or spa are open the way they normally sit.
- Check the breaker. Reset it once if it's tripped. If it trips again, leave it off.
- Write down any error code. Note what the display shows before you turn anything off.
The MasterTemp guide adds one more point. A two speed pump on low may not build enough pressure to run the heater. Try high speed before you assume the heater failed.
What do pool heater error codes mean?
Most codes point to a safety switch that stopped the heater on purpose. According to Pentair's MasterTemp guide, the code ERR PS means the water pressure switch is open, with no water flow through the heater. Write the code down before you reset anything.
Other codes on that model cover air flow, ignition, and temperature sensors. Use the code as a clue, not a repair list.
A flow code sends you back to the pump, filter, and valves. An ignition or sensor code means it's time to call a technician.
Why won't a heat pump heat in cool months?
Because it pulls heat from the outside air. An archived U.S. Department of Energy page on heat pump swimming pool heaters says they work efficiently while outside air stays above the 45 to 50 degree range. Run it during the warmest part of the day and cover the pool overnight.
Below that range, the heater runs longer and gains less ground. Expect slower progress on the coldest nights, even from a healthy heat pump. Our guide on how to size a pool heater explains why a small heat pump struggles more in winter.
Gas heater runs but the water stays cold
When a gas heater fires but the pool barely warms, look at these causes:
- Low flow from a dirty filter or a pump running too slowly
- Scale built up inside the heat exchanger
- A heater that's too small for the pool and the season
- Heat loss from wind and an uncovered pool overnight
- A faulty temperature sensor reading the water wrong
The first one you can fix with a filter cleaning. The rest need testing. Our post on what a new pool heater does to your energy bill covers the running cost side.
When to stop and call a pro
Stop when the next step means opening the heater cabinet, touching the gas line, or bypassing a switch. The MasterTemp guide says only qualified, trained service technicians with proper test equipment should service the heater. It also says not to use a heater if any part has been under water.
Call a pro if you notice any of these:
- The breaker trips again after one reset
- The heater shows an ignition, sensor, or temperature code
- You hear repeated clicking with no flame
- You see soot, scorching, or melted wiring
- Water is leaking from the heater
If you smell gas near the heater
Leave the area and call from somewhere safe. Long Beach Utilities' natural gas safety page says to evacuate and call its emergency line at (562) 570-2140, or 911.
Don't light anything, flip switches, or try to find the leak. Neighbors outside the city's gas service area should use their own gas company's emergency number. Once the gas side is cleared, have a technician check the heater before you run it again.
Repair or replace an old pool heater
Repair usually makes sense on a newer heater with one failed part, like an igniter or a sensor. Replacement starts to make sense when the heat exchanger is leaking or badly scaled, or the heater keeps failing.
Get a diagnosis before you decide. Our comparison of repairing versus replacing a pool heater walks through the tradeoffs in more detail.
The questions Long Beach pool owners ask most when the heater stops working, answered plainly.
Want the heater checked by a pro?
A cold pool in November is fixable, and it doesn't always mean a new heater. At Adam's Pool & Spa, I'll check flow, codes, and the heater itself. Then I'll tell you what it needs before any work starts. We work across Long Beach and nearby neighborhoods, and we're Jandy Certified and a Pentair Expert Installer. Schedule a visit and I'll take it from there.
Adam is the founder, owner, and lead technician of Adam's Pool & Spa, working on pools in Long Beach and nearby LA County for about fifteen years. He is Jandy Certified and a Pentair Expert Installer, and he built the business on education-first, anti-pressure service, including the "Pool School" session each new client gets.
Frequently asked questions
Why won't my pool heater turn on?
The most common reasons a homeowner can check are a pump that isn't running, a dirty filter or basket cutting flow, valves set the wrong way, or a heater that's off or set below the water temperature. A gas heater won't fire without enough water flow through it. Past those checks, the cause is inside the heater and needs a qualified technician.
Why does my pool heater turn on but not heat the water?
A heat pump may simply be working against cool air. A DOE guide says heat pump pool heaters work efficiently while the outside air stays above the 45 to 50 degree range. A gas heater that runs but doesn't warm the pool may have low flow, a scaled heat exchanger, or a sizing problem, which a technician can sort out.
Can I reset my pool heater myself?
Turning the heater off and back on at its own control is fine, and some error codes clear once the cause is fixed. Don't bypass switches, open the gas valve, or take the cover off. Pentair's MasterTemp guide says only qualified, trained service technicians with test equipment should service the heater.
What should I do if I smell gas near my pool heater?
Leave the area right away and call from a safe place. In Long Beach, the city's gas utility lists its emergency line as (562) 570-2140, or you can call 911. Don't flip switches or try to find the leak yourself. If another company supplies your gas, follow its emergency steps.
Should I repair or replace a pool heater that keeps failing?
It depends on the heater's age, the part that failed, and how often it's failed before. A newer heater with one bad part is usually worth repairing. An older unit with a leaking or badly scaled heat exchanger often isn't. Get a diagnosis first, then compare the repair quote with a replacement.


